ZBZ Bearing ZBZ BearingsWafangdian Zhongbei Bearing
Star Product 01 / Back-up Bearings

Back-up Bearings
A Critical Link in the Precision Chain

Engineered for the backing-roll assemblies (saddles) of Sendzimir 20-high and multi-roll cold rolling mills. ZBZ manufactures to your mill model and saddle drawings: P5 as standard, P4 on request — benchmarked against the precision of Japanese KOYO and other international brands, delivered faster and serviced closer to home.

Home / Star Products / Back-up Bearings
What it is

The Outer Ring Is the Roll Surface

BU-00

How It Works

In Sendzimir 20-high and 12-high cluster mills, every intermediate and backing roll is carried by several back-up bearings seated in fixed saddle blocks, stacked in a tower arrangement.

A back-up bearing is essentially a multi-row cylindrical roller bearing with a heavy-section outer ring — the outer diameter of the outer ring forms the roll surface itself, separated from the strip only by a thin sleeve. It plays three roles at once:

  • Support member: closely spaced roller rows give the roll cluster its radial stiffness;
  • Rolled-surface carrier: the OD of the outer ring is the roll face — its geometry maps straight into strip shape;
  • Precision link: at the end of the work-roll → intermediate-roll → backing-roll → saddle precision chain, every micron of error reaches the roll gap.

That is why back-up bearings are described as "judged in microns": one outer ring out of tolerance on a roll carrying three others leaves a visible mark on the strip.

ZBZ back-up bearing: heavy-section outer ring with multi-row cylindrical rollers
ZBZ back-up bearing: heavy-section outer ring, multi-row cylindrical rollers — the OD is the roll face, ground to match the saddle bore
Engineering

Four Details That Decide Strip Shape

What separates a back-up bearing from an ordinary cylindrical roller bearing lives entirely in the details.

BU-01

Heavy Outer Ring & Profiled Rollers

The outer ring wall is far thicker than a general-purpose bearing to withstand high contact stress and creep in the saddle bore. Rollers carry a logarithmic or crowned profile that removes edge stress concentration under high-frequency pulsating loads — the first line of defence for life.

BU-02

Matched Sets (Single-Micron Mutual Difference)

A backing roll typically carries 2–4 back-up bearings. ZBZ measures every finished bearing individually, grinds to set and ships as a matched group with the OD mutual difference held to single microns and the measured values supplied — ready to mount, no on-site selection needed.

BU-03

Material & Heat Treatment

Rollers and raceways use electro-slag remelted (ESR) bearing steel with oxygen and inclusion levels controlled to premium standards; through hardening plus stabilising tempering keeps dimensions stable under high-speed rolling temperature rise.

BU-04

Cage & Anti-Creep Design

Cage design, pocket clearance and guiding are verified against your actual speed spectrum — preventing skidding at high speed and roller skew under slow heavy passes. Outer-ring-to-saddle fits are ground to drawing to suppress ring creep.

Specifications

Typical Capability Range

Back-up bearings have no generic catalogue — each one follows a mill model and a saddle drawing. Below is ZBZ's regular manufacturing envelope.

ItemZBZ Capability
ConstructionMulti-row cylindrical rollers, heavy-section outer ring; built to mill model, saddle drawing or sample reverse-engineering
Precision classP5 standard, P4 on request; all items of running accuracy and OD tolerance inspected
RollersESR steel, logarithmic / crowned profile, super-finished surfaces
Matched setsSet mutual OD difference held to single microns; measured values shipped with each set
ClearanceCalculated from load spectrum, speed spectrum and fit interference; stated in the selection proposal
CageMachined solid cage; material and pocket clearance selected per speed spectrum
FitsOuter ring ground to match the actual saddle bore; inner ring to the roll journal per drawing
LubricationCompatible with emulsion / oil-air systems; supplied to suit existing pipework
DocumentationMaterial certificates, heat-treatment reports, full inspection records (worded to EN 10204 3.1)
What we need for selection Provide the mill model (e.g. ZR 20-high), saddle drawings or a used sample, strip material and width, pass reduction, rolling speed — our engineers return a complete proposal covering precision class, fits, clearance and lubrication within 72 hours of receiving full operating data.
Failure Analysis

Understand the Failure, Then Build the Bearing

Back-up bearings are among the most failure-prone parts on a cold rolling line. ZBZ designs backwards from every failure path.

Failure modeTypical root causeZBZ countermeasure
Outer-ring creep wearPoor ring-to-bore fit; the ring micro-moves in the saddle bore and wears itOuter ring ground to the measured saddle bore, fit verified unit by unit; saddle-bore repair advice where needed
Raceway / roller edge spallingPulsating loads plus roll-stack deflection concentrate stress at roller endsLogarithmic roller profiles distribute contact stress evenly along the line
Skidding & smearingRoller slip during slow heavy passes or acceleration damages the racewayCage and lubrication verified against the real speed spectrum; pocket clearance optimised to cut drag
Strip marks (chatter)Excessive OD mutual difference or vibration in the set; uneven roll gapMatched-set selection plus factory vibration grading; measured values shipped with the goods
Early fatigue spallingMaterial inclusions acting as fatigue initiatorsESR steel plus stabilised heat treatment, inclusions controlled to premium levels
Vertical Comparison

Back-up Bearings vs "Making Do with Ordinary Bearings"

Some users try to adapt general-purpose cylindrical roller bearings. Does it really save money?

DimensionAdapted ordinary bearingZBZ back-up bearing
Outer-ring strengthWall sized for general duty; thin for saddle contact stressHeavy-section ring designed for saddle-bore contact
Roller profileStraight or generic profile; edge stress concentrationLogarithmic / crowned profile optimised for pulsating loads
Set consistencyBought as singles; OD mutual difference uncontrolledSupplied as ground matched sets to single-micron mutual difference
Fit matchStandard tolerances; cannot match a worn saddle boreGround to the measured bore, unit by unit
True costShort life, recurring strip marks, repeated unplanned stopsDesigned forward from your duty; install once, keep the mill running

The money a back-up bearing saves was never in its purchase price — it's in the precision chain it holds and the stops it prevents.

Benchmark

ZBZ vs International Brands (KOYO as Representative)

Japanese KOYO (JTEKT) is the representative international brand in multi-roll mill back-up bearings, known for high-precision multi-row cylindrical roller construction and long service on stainless and silicon-steel lines. ZBZ does not dispute that standing — we offer a different answer on delivery, service and customisation, at the same precision standard.

DimensionInternational brands (KOYO etc.)ZBZ back-up bearings
PrecisionP4 / P5, the industry benchmark with a mature tolerance systemManufactured to the same precision classes and standards; full inspection records shipped, third-party re-inspection welcome
Profiling & matched setsMature profiling and set-selection technology, supplied from their product systemThe same profiling and matched-set capability — ground to your saddle drawing, not limited by any catalogue
Lead timePlanned in overseas plants; even catalogue items carry long lead times, specials longer still — an unplanned stop cannot waitDomestic planning with markedly shorter lead times; urgent orders assessed for expedited supply, emergency pieces first
CustomisationStandard product system; out-of-catalogue specials carry high barriers and long cyclesMaterial, heat treatment, clearance, cage and lubrication interfaces all engineered to drawing, with life re-checked
Field serviceTechnical support overseas; language, time zones and travel cost slow everything downEngineers in-country: proposal within 72 hours, on-site support for mounting, clearance setting and failure analysis
Discontinued itemsParts for older mills discontinued or transferred — no original source remainsReverse-engineered from drawings or samples; saddle bores and mounting practice unchanged, old mills keep rolling
CommunicationLayered through agents; drawings and specifications repeatedly re-interpretedEngineer-to-engineer, zero translation loss, changes confirmed the same day
Our honest advice If your imported supply is stable and well stocked, we respect that. The moment you hit any of these four — a lead time you cannot wait out, a special nobody will quote, a discontinued part with no source, a field problem nobody comes to see — ZBZ is the alternative in your drawer. Start with one position on trial.
Applications

Where ZBZ Back-up Bearings Work

20-high mill maintenance: mill housing open, tower roll system and back-up bearing saddles visible
20-high mill maintenance: with the housing open, the tower roll system is fully exposed — every back-up bearing in it takes part in deciding strip shape
AP-01

Sendzimir 20-High Mills

The workhorse of precision stainless and silicon-steel rolling. Dense bearing counts and the highest precision demands make the tower roll system ZBZ's core battlefield.

AP-02

12-High / Multi-Roll Mills

Medium and narrow strip and special alloys. High volumes of mid-range back-up bearings — where matched sets and short lead times matter most.

AP-03

Precision Foil Mills

Copper foil, aluminium foil and ultra-thin strip. Extreme shape sensitivity pushes OD mutual difference and vibration grading requirements to their limits.

AP-04

Legacy Imported Mills

Earlier imported Sendzimir mills whose original parts are discontinued or hopelessly long-lead. ZBZ reverse-engineers from samples — old mills never stop for one bearing.

AP-05

Mill Overhaul Packages

Overhaul windows are short. ZBZ plans whole sets of back-up bearings to one delivery date, group-inspected and ready to install together.

AP-06

Duty-Upgrade Retrofits

Product changeovers can shorten bearing life dramatically. ZBZ recalculates clearance and profile for the new duty — a back-up bearing made for your strip.

Deep Dive

20-High Mills & Cold-Rolled Silicon Steel: The Toughest Stage a Back-up Bearing Faces

Inside a Sendzimir 20-high mill, rolling force starts at the small-diameter work rolls and passes level by level through the tower roll system until every newton lands on the back-up bearings. What you roll decides what the bearing endures — and cold-rolled silicon steel is among the most punishing strip grades of all.

Sendzimir 20-high tower roll system: back-up rolls and saddles arranged level by level
The Sendzimir 20-high tower, photographed live: heavy back-up rolls mounted in saddles, level by level — rolling force passes down until every newton lands on the back-up bearings
SS-01

Hard Material — Heavy Force

High-grade silicon steel carries 2.5%–3.5% silicon: hard, work-hardening fast, and demanding noticeably higher rolling force than plain carbon strip. Load peaks and acceleration shocks on the back-up bearings rise accordingly.

SS-02

Thin Gauge — Micron Tolerances

Finished cold-rolled silicon steel is commonly below 0.35 mm; grain-oriented grades run down to 0.20–0.27 mm. Thickness tolerances are counted in microns — any roll-gap disturbance is written straight into the gauge curve.

SS-03

Magnetic Properties — Shape Is Performance

Core loss and magnetic induction define the product. Thickness uniformity and strip shape flow directly into annealing, lamination stacking and magnetic consistency. On a silicon steel line, shape defects are performance defects.

Charging a cold-rolled silicon steel coil onto the uncoiler
Charging a silicon steel coil: thin gauge, high hardness — every coil tests the back-up bearings
DE-01

What This Duty Demands of a Back-up Bearing

OD mutual difference must be held tighter still, or the tower loads unevenly and localized bearings age early. Rollers need end profiling to avoid edge stress concentration under heavy force; anti-creep features must survive frequent speed changes; vibration grading decides whether chatter marks appear on the thin strip.

DE-02

The ZBZ Answer

Clearance and roll profiling calculated from your mill model, strip grade and pass schedule; matched-set delivery; P5/P4 precision with low-vibration options; reverse-engineering from samples for legacy mills. A back-up bearing built to silicon steel duty — not a catalogue compromise.

Service

From Enquiry to Installation: A Four-Step Loop

ST-01

① Intake · Proposal in 72 h

Within 72 hours of receiving your mill model, saddle drawings and duty data, we issue a proposal covering precision class, fits, clearance and lubrication.

ST-02

② Drawing Confirmation · Sample Scanning

No drawings? Send one used bearing — we scan and draw it free of charge; production starts only after both sides confirm the drawing.

ST-03

③ 100% Inspection · Set Delivery

Every piece fully inspected, measured set values shipped with the goods; material certificates, heat-treatment and inspection records (worded to EN 10204 3.1) included.

ST-04

④ Delivery Support · Life Tracking

Engineers on site for mounting and clearance setting when needed; we track in-service performance and analyse returned failed parts free of charge with an improvement report.

ST-05

Urgent Channel

Unplanned stop that cannot wait? Tell us the deadline and the position — we assess supplying an emergency piece first, with the full part to follow.

FAQ

Six Questions Buyers Ask Most

Q1: Can you build from a used bearing instead of a drawing?

Yes. Ship the old part to Wafangdian — we reverse-engineer and draw it free of charge and start production after mutual confirmation, to the same precision standard as build-to-print.

Q2: Is P4 precision really repeatable? How do we verify it?

Every piece is fully inspected with measured records shipped; key items can be witnessed by you or a third party at our works, and third-party metrology re-inspection after delivery is welcome.

Q3: Can ZBZ bearings run mixed with imported ones on the same roll?

Yes — provided OD groups match. We grind new parts into groups aligned with the measured values of your in-use bearings; send us those measurements or a sample.

Q4: What is the minimum order quantity?

Ordering per roll (2–4 bearings) is the norm, but a single bearing trial order is welcome — we encourage proving life and strip-shape performance on one position first.

Q5: Marks still appear on the strip after fitting — now what?

First rule out sleeves, work rolls and assembly clearance. Share the symptom and parameters and a ZBZ engineer joins the analysis; if the bearing is at fault, return it for a free failure analysis and improvement report.

Q6: How short can lead time get?

Standard items ship to plan; urgent orders get an expedited assessment — an emergency piece first, the full part to follow. Exact commitments are made in writing at selection.

Send Us Your Mill Model and Saddle Drawings

A back-up bearing selection proposal covering precision, fits, clearance and lubrication within 72 hours — compare first, decide later.